SBC MT 01 Especificaciones descargar pdf (Pagina 74)

GROUP S.P.A.

MT SBC 01

Standard function: Privacy

This function enables you to set the Privacy function on the

pushbutton. If enabled, it allows you to disable temporarily the

ringtone of the interphone in response to calls from the external

unit and porter switchboard Art. 1998A.

The landing call and intercom call ringtones are not disabled.

To enable or disable the Privacy function, press the monitor or

interphone pushbutton on which the function has been

programmed for 2 seconds; selection of the enabled state is

also indicated by the illumination of the indicator LED.

The function does not require the programming of any

Parameter.

Standard function: Doctor

This function enables you to set the Doctor function on the

pushbutton.

Enablement is also indicated by the signalling LED lighting up.

When there are several users with the same user code, set the

Doctor function on only one of the units enabled for this.

To enable or disable the Doctor function, press the monitor or

interphone pushbutton on which the function has been

programmed for 2 seconds; selection of the enabled state is

also indicated by the illumination of the indicator LED.

The function does not require the programming of any

Parameter.

Standard function: Intercom

This function enables you to set the intercom call function on

the pushbutton.

The function is available only for intercom systems that use

internal extensions Art. 4897, 5714CI, 4784I, 2618 and 2418W.

Group Intercom

This function enables you to set the group intercom call

function on the pushbutton.

The function is available only for intercom systems that use

internal extensions Art. 4897, 5714CI, 4784I, 2618 and 2418W.

Function

[Coded Actuator.]

▼

PARAMETER

Fig. 19

Internal extension common programming

operations

The paragraphs below describe programming operations which are

common to all programmable internal extensions Art. 4897, 5714C,

5714CI, 4784, 4784I, 2618 and 2418W.

How to assign a standard function to a pushbutton

To programme a pushbutton you must:

1. Connect the hand-held programmer to the device to be

programmed, see page 68.

2. Use the and keys to select the Prog. Pushbuttons

menu and then press .

3. Use the and keys to select the pushbutton that you

want to programme and then press .

4. Use the and keys to select Standard Func., and

then press .

5. Using the and keys, scroll through the available

functions until the display shows the function you want to

programme on the pushbutton.

6. If necessary, go the to parameter field using and and

enter the requested numerical value (see standard functions

description on page 71) using the keypad of the programmer.

7. Press and make sure that the following message

appears:

If the operation is not successful, the display will show the

message:

If the operation is not permitted, the display will show an error

message . Setting a remote camera on a

secondary bracket/monitor is incompatible and therefore not

permitted.

8. After a few seconds the display shows the pushbutton selection

menu for any further operations on the extension.

EXAMPLE: setting Actuator with code 35 on pushbutton 2 of the

monitor.

“Oper. failed!”

“Transm. failed!”

“Operation OK”

“Transmission OK”

Sel

Art. 5714C

Connection OK!

—————————

Prog. pushbuttons

Read pushbuttons

Pushbutton 1

Pushbutton 2

Pushbutton 3

Reset pushbutton

Standard Func.

Camera cycle

Function:

Coded Actuator

parameter

[ ]

OPERATION DISPLAY

Connect hand-held programmer

Art. 1251/A to bracket 5714C.

Select Prog. Pushbuttons and

press .

Select Pushbutton 2 and press

Select Standard. Func. and press

Use the and

keys to scroll the Coded

Actuator function.

Sel

1 2 ... 69 70 71 72 73 74 75 76 77 78 79 ... 131 132

Comentarios a estos manuales

Sin comentarios

SBC MT 01 Especificaciones Pagina 74

Comentarios a estos manuales